Differences

This shows you the differences between two versions of the page.

--- linux:raspberry:picam:motion [2015/06/01 21:01] – lunetikk
+++ linux:raspberry:picam:motion [2022/06/13 18:57] (current) – lunetikk
@@ Line 1: / Line 1: @@
-===== Copyjob =====
+===== Motion =====
+==== Installation ====
+<code>apt-get install motion</code>
+==== Configuration ====
+=== motion.conf ===
+see my configfile below...
+=== Maskfile ===
+The maskfile is used to ignore certain areas with moving objects (like trees, pedestrians, cars) which normally would cause motion to capture pictures/videos. The file must have the same width and height as the picture captured by your camera.
+Take a captured picture, paint all the correct areas white, the ones you want to ignore black. //You can also use different gray tones for different sensitivity (never tried).//
+Copy the picture to your Raspberry and convert it to the correct format.
-This script copies all your .jpg and .avi captures to a mounted NAS. Before it does so, it will check if there is a directory with the date of today. If it doesnt exist it will create one with the subdirectories "Videos" and "Pictures". After that it copies the files to a non-chaning local directory and then from there to the created directories on your NAS. The script can be executed via crontab.
-\\
-First mount your NAS.
-\\
 <code>
-mount -t cifs //192.168.178.xxx/PATH/ /media/nasdir/
+djpeg -grayscale -pnm <YOURPICTURE> > maskfile.pgm
 </code>
-Make sure you can access it and that you can see files. If you already have files at "%%//%%192.168.178.xxx/PATH/" you can use <code>ls -al /media/nasdir/</code>
-Also create a file with <code>touch /media/nasdir/test</code> and check if it has been created.
-<code sh copyjob.sh>
+If djpeg is missing, install the following package (libjpeg-progs - Programs for manipulating JPEG files)
-#!/bin/bash
+<code>
-DATE=`date +%d_%m_%Y`
+apt-get install libjpeg-progs
-BASEPATH=/records/
+</code>
-COPYPATH=/records/copy/
-NETPATH=/media/nasdir/
-if [ ! -d "$NETPATH$DATE" ]; then
+Place your maskfile next to your "motion.conf" (in /etc/motion) and set the maskfile in your config (syntax: mask_file <FILE>).
-  mkdir $NETPATH$DATE
-  mkdir $NETPATH$DATE/Videos
-  mkdir $NETPATH$DATE/Pictures
-fi
-NETPATHAVI=$NETPATH$DATE/Videos
+[[http://www.lavrsen.dk/foswiki/bin/view/Motion/ConfigOptionMaskFile|How to create a Maskfile]]
-NETPATHJPG=$NETPATH$DATE/Pictures
-mv $BASEPATH*.avi $COPYPATH
+==== Troubleshooting ====
-sleep 10
-mv $BASEPATH*.jpg $COPYPATH
-sleep 10
-mv $COPYPATH*.avi $NETPATHAVI
+=== libavformat error ===
-sleep 10
-mv $COPYPATH*.jpg $NETPATHJPG
+"motion: error while loading shared libraries: libavformat.so.53: cannot open shared object file: no such file or directory"
-sleep 10
+You might have to install some dependencies
+<code>apt-get install -y libjpeg62 libjpeg62-dev libavformat53 libavformat-dev libavcodec53 libavcodec-dev libavutil51 libavutil-dev libc6-dev zlib1g-dev libmysqlclient18 libmysqlclient-dev libpq5 libpq-dev</code>
+If some are not found, try to get the right version for your current distribution via
+<code>apt-cache search <package></code>
+=== /dev/video0 not found ===
+"vid_v4lx_start: Failed to open video device /dev/video0: No such file or directory"
+Activate the module, /dev/video0 should be there afterwards
+<code>modprobe bcm2835-v4l2</code>
+and add the module to /etc/modules as a new line (persistent)
+<code>bcm2835-v4l2</code>
+=== libavformat error ===
+<code>
+[1:ml1] [NTC] [ALL] [Jun 13 18:42:16] mlp_actions: End of event 1
+[1:ml1] [NTC] [ALL] [Jun 13 18:42:16] motion_loop: Thread exiting
+[1:ml1] [NTC] [VID] [Jun 13 18:42:16] vid_close: Cleaning up V4L2 device
+[1:ml1] [NTC] [VID] [Jun 13 18:42:16] v4l2_cleanup: Closing video device /dev/video0
+[0:motion] [NTC] [ALL] [Jun 13 18:42:17] main: Threads finished
+[0:motion] [NTC] [ALL] [Jun 13 18:42:17] main: Motion terminating
 </code>
-Make sure you use <code>chmod +x cronjob.sh</code> to make it executeable.\\
+Motion just stops. If you activated "daemon mode" via config you might need to edit your servicefile.
-Create a cronjob for it by inserting the following line to the end in<code> vi /etc/crontab</code> <code sh crontab>0 * * * * /records/copyjob.sh >/dev/null 2>&1</code>
-The job will be executed everytime the clock hits 0 minutes (for example 1:00pm 2.00am...)
+Edit /lib/systemd/system/motion.service
+<code>
+ExecStart=/usr/bin/motion
+to
+ExecStart=/usr/bin/motion -n
+</code>
+then
+<code>
+systemctl daemon-reload
+systemctl restart motion.service
+</code>
+[[https://github.com/Motion-Project/motion/pull/303/commits/34faa49adf33a1e12da74644800455139886a241|Github commit]]
+==== My configurationfile ====
+This is the dozencrows config with my values, some things have changed in the current "apt-get"-version. Most of the config is the same, just compare it with the new one
+<code sh motion.conf>
+# /etc/motion.conf
+#
+# This config file was generated by motion mmaltest
+############################################################
+# Daemon
+############################################################
+# Start in daemon (background) mode and release terminal (default: off)
+daemon on
+#File to store the process ID, also called pid file. (default: not defined)
+process_id_file /var/run/motion/motion.pid
+############################################################
+# Basic Setup Mode
+############################################################
+# Start in Setup-Mode, daemon disabled. (default: off)
+setup_mode off
+# Use a file to save logs messages, if not defined stderr and syslog is used. (default: not defined)
+logfile /recordings/motion.log
+# Level of log messages [1..9] (EMR, ALR, CRT, ERR, WRN, NTC, ERR, DBG, ALL). (default: 6 / NTC)
+log_level 5
+# Filter to log messages by type (COR, STR, ENC, NET, DBL, EVT, TRK, VID, ALL). (default: ALL)
+log_type all
+###########################################################
+# Capture device options
+############################################################
+# Videodevice to be used for capturing  (default /dev/video0)
+# for FreeBSD default is /dev/bktr0
+videodevice /dev/video0
+# v4l2_palette allows to choose preferable palette to be use by motion
+# to capture from those supported by your videodevice. (default: 17)
+# E.g. if your videodevice supports both V4L2_PIX_FMT_SBGGR8 and
+# V4L2_PIX_FMT_MJPEG then motion will by default use V4L2_PIX_FMT_MJPEG.
+# Setting v4l2_palette to 2 forces motion to use V4L2_PIX_FMT_SBGGR8
+# instead.
+#
+# Values :
+# V4L2_PIX_FMT_SN9C10X : 0  'S910'
+# V4L2_PIX_FMT_SBGGR16 : 1  'BYR2'
+# V4L2_PIX_FMT_SBGGR8  : 2  'BA81'
+# V4L2_PIX_FMT_SPCA561 : 3  'S561'
+# V4L2_PIX_FMT_SGBRG8  : 4  'GBRG'
+# V4L2_PIX_FMT_SGRBG8  : 5  'GRBG'
+# V4L2_PIX_FMT_PAC207  : 6  'P207'
+# V4L2_PIX_FMT_PJPG    : 7  'PJPG'
+# V4L2_PIX_FMT_MJPEG   : 8  'MJPEG'
+# V4L2_PIX_FMT_JPEG    : 9  'JPEG'
+# V4L2_PIX_FMT_RGB24   : 10 'RGB3'
+# V4L2_PIX_FMT_SPCA501 : 11 'S501'
+# V4L2_PIX_FMT_SPCA505 : 12 'S505'
+# V4L2_PIX_FMT_SPCA508 : 13 'S508'
+# V4L2_PIX_FMT_UYVY    : 14 'UYVY'
+# V4L2_PIX_FMT_YUYV    : 15 'YUYV'
+# V4L2_PIX_FMT_YUV422P : 16 '422P'
+# V4L2_PIX_FMT_YUV420  : 17 'YU12'
+#
+v4l2_palette 17
+# The video input to be used (default: -1)
+# Should normally be set to 0 or 1 for video/TV cards, and -1 for USB cameras
+input -1
+# The video norm to use (only for video capture and TV tuner cards)
+# Values: 0 (PAL), 1 (NTSC), 2 (SECAM), 3 (PAL NC no colour). Default: 0 (PAL)
+norm 0
+# The frequency to set the tuner to (kHz) (only for TV tuner cards) (default: 0)
+frequency 0
+# Rotate image this number of degrees. The rotation affects all saved images as
+# well as movies. Valid values: 0 (default = no rotation), 90, 180 and 270.
+rotate 0
+# Image width (pixels). Valid range: Camera dependent, default: 352
+width 1280
+# Image height (pixels). Valid range: Camera dependent, default: 288
+height 720
+# Maximum number of frames to be captured per second.
+# Valid range: 2-100. Default: 100 (almost no limit).
+framerate 15
+# Minimum time in seconds between capturing picture frames from the camera.
+# Default: 0 = disabled - the capture rate is given by the camera framerate.
+# This option is used when you want to capture images at a rate lower than 2 per second.
+minimum_frame_time 0
+# URL to use if you are using a network camera, size will be autodetected (incl http:// ftp:// mjpg:// or file:///)
+# Must be a URL that returns single jpeg pictures or a raw mjpeg stream. Default: Not defined
+; netcam_url value
+# Username and password for network camera (only if required). Default: not defined
+# Syntax is user:password
+; netcam_userpass value
+# The setting for keep-alive of network socket, should improve performance on compatible net cameras.
+# off:   The historical implementation using HTTP/1.0, closing the socket after each http request.
+# force: Use HTTP/1.0 requests with keep alive header to reuse the same connection.
+# on:    Use HTTP/1.1 requests that support keep alive as default.
+# Default: off
+netcam_keepalive off
+# URL to use for a netcam proxy server, if required, e.g. "http://myproxy".
+# If a port number other than 80 is needed, use "http://myproxy:1234".
+# Default: not defined
+; netcam_proxy value
+# Set less strict jpeg checks for network cameras with a poor/buggy firmware.
+# Default: off
+netcam_tolerant_check off
+# Path to file containing raw captured YUV frames from which to read input
+ Default: Not defined
+; filecam_path value
+# Name of camera to use if you are using a camera accessed through OpenMax/MMAL
+ Default: Not defined
+mmalcam_name vc.ril.camera
+# Camera control parameters (see raspivid/raspistill tool documentation)
+ Default: Not defined
+; mmalcam_control_params value
+# Use the still camera output - limits frame rate, but can show more of frame
+ Default: off
+mmalcam_use_still off
+# Path to file where raw dump of camera YUV capture will be written (for testing, profiling & debugging)
+ Default: Not defined
+; mmalcam_raw_capture_file value
+# Let motion regulate the brightness of a video device (default: off).
+# The auto_brightness feature uses the brightness option as its target value.
+# If brightness is zero auto_brightness will adjust to average brightness value 128.
+# Only recommended for cameras without auto brightness
+auto_brightness off
+# Set the initial brightness of a video device.
+# If auto_brightness is enabled, this value defines the average brightness level
+# which Motion will try and adjust to.
+# Valid range 0-255, default 0 = disabled
+brightness 0
+# Set the contrast of a video device.
+# Valid range 0-255, default 0 = disabled
+contrast 0
+# Set the saturation of a video device.
+# Valid range 0-255, default 0 = disabled
+saturation 0
+# Set the hue of a video device (NTSC feature).
+# Valid range 0-255, default 0 = disabled
+hue 0
+############################################################
+# Round Robin (multiple inputs on same video device name)
+############################################################
+# Number of frames to capture in each roundrobin step (default: 1)
+roundrobin_frames 1
+# Number of frames to skip before each roundrobin step (default: 1)
+roundrobin_skip 1
+# Try to filter out noise generated by roundrobin (default: off)
+switchfilter off
+############################################################
+# Motion Detection Settings:
+############################################################
+# Threshold for number of changed pixels in an image that
+# triggers motion detection (default: 1500)
+threshold 1500
+# Automatically tune the threshold down if possible (default: off)
+threshold_tune off
+# Noise threshold for the motion detection (default: 32)
+noise_level 32
+# Automatically tune the noise threshold (default: on)
+noise_tune on
+# Despeckle motion image using (e)rode or (d)ilate or (l)abel (Default: not defined)
+# Recommended value is EedDl. Any combination (and number of) of E, e, d, and D is valid.
+# (l)abeling must only be used once and the 'l' must be the last letter.
+# Comment out to disable
+despeckle_filter EedDl
+# Detect motion in predefined areas (1 - 9). Areas are numbered like that:  1 2 3
+# A script (on_area_detected) is started immediately when motion is         4 5 6
+# detected in one of the given areas, but only once during an event.        7 8 9
+# One or more areas can be specified with this option. Take care: This option
+# does NOT restrict detection to these areas! (Default: not defined)
+; area_detect value
+# PGM file to use as a sensitivity mask.
+# Full path name to. (Default: not defined)
+# mask_file value
+mask_file /recordings/greyscale/mask.pgm
+# Dynamically create a mask file during operation (default: 0)
+# Adjust speed of mask changes from 0 (off) to 10 (fast)
+smart_mask_speed 0
+# Ignore sudden massive light intensity changes given as a percentage of the picture
+# area that changed intensity. If set to 1, motion will do some kind of
+# auto-lightswitch. Valid range: 0 - 100 , default: 0 = disabled
+lightswitch 0
+# Picture frames must contain motion at least the specified number of frames
+# in a row before they are detected as true motion. At the default of 1, all
+# motion is detected. Valid range: 1 to thousands, recommended 1-5
+minimum_motion_frames 1
+# Specifies the number of pre-captured (buffered) pictures from before motion
+# was detected that will be output at motion detection.
+# Recommended range: 0 to 5 (default: 0)
+# Do not use large values! Large values will cause Motion to skip video frames and
+# cause unsmooth movies. To smooth movies use larger values of post_capture instead.
+pre_capture 1
+# Number of frames to capture after motion is no longer detected (default: 0)
+post_capture 3
+# Event Gap is the seconds of no motion detection that triggers the end of an event.
+# An event is defined as a series of motion images taken within a short timeframe.
+# Recommended value is 60 seconds (Default). The value -1 is allowed and disables
+# events causing all Motion to be written to one single movie file and no pre_capture.
+# If set to 0, motion is running in gapless mode. Movies don't have gaps anymore. An
+# event ends right after no more motion is detected and post_capture is over.
+event_gap 60
+# Maximum length in seconds of a movie
+# When value is exceeded a new movie file is created. (Default: 0 = infinite)
+max_movie_time 600
+# Always save images even if there was no motion (default: off)
+emulate_motion off
+############################################################
+# Image File Output
+############################################################
+# Output 'normal' pictures when motion is detected (default: on)
+# Valid values: on, off, first, best, center
+# When set to 'first', only the first picture of an event is saved.
+# Picture with most motion of an event is saved when set to 'best'.
+# Picture with motion nearest center of picture is saved when set to 'center'.
+# Can be used as preview shot for the corresponding movie.
+output_pictures on
+# Output pictures with only the pixels moving object (ghost images) (default: off)
+output_debug_pictures off
+# The quality (in percent) to be used by the jpeg compression (default: 75)
+quality 100
+# Type of output images
+# Valid values: jpeg, ppm (default: jpeg)
+picture_type jpeg
+############################################################
+# FFMPEG related options
+# Film (movie) file output, and deinterlacing of the video input
+# The options movie_filename and timelapse_filename are also used
+# by the ffmpeg feature
+############################################################
+# Use ffmpeg to encode movies in realtime (default: off)
+ffmpeg_output_movies on
+# Use ffmpeg to make movies with only the pixels moving
+# object (ghost images) (default: off)
+ffmpeg_output_debug_movies off
+# Use ffmpeg to encode a timelapse movie
+# Default value 0 = off - else save frame every Nth second
+ffmpeg_timelapse 0
+# The file rollover mode of the timelapse video
+# Valid values: hourly, daily (default), weekly-sunday, weekly-monday, monthly, manual
+ffmpeg_timelapse_mode daily
+# Bitrate to be used by the ffmpeg encoder (default: 400000)
+# This option is ignored if ffmpeg_variable_bitrate is not 0 (disabled)
+ffmpeg_bps 500000
+# Enables and defines variable bitrate for the ffmpeg encoder.
+# ffmpeg_bps is ignored if variable bitrate is enabled.
+# Valid values: 0 (default) = fixed bitrate defined by ffmpeg_bps,
+# or the range 2 - 31 where 2 means best quality and 31 is worst.
+ffmpeg_variable_bitrate 0
+# Codec to used by ffmpeg for the video compression.
+# Timelapse movies are always made in mpeg1 format independent from this option.
+# Supported formats are: mpeg1 (ffmpeg-0.4.8 only), mpeg4 (default), and msmpeg4.
+# mpeg1 - gives you files with extension .mpg
+# mpeg4 or msmpeg4 - gives you files with extension .avi
+# msmpeg4 is recommended for use with Windows Media Player because
+# it requires no installation of codec on the Windows client.
+# swf - gives you a flash film with extension .swf
+# flv - gives you a flash video with extension .flv
+# ffv1 - FF video codec 1 for Lossless Encoding ( experimental )
+# mov - QuickTime ( testing )
+# ogg - Ogg/Theora ( testing )
+ffmpeg_video_codec msmpeg4
+# Use ffmpeg to deinterlace video. Necessary if you use an analog camera
+# and see horizontal combing on moving objects in video or pictures.
+# (default: off)
+ffmpeg_deinterlace off
+############################################################
+# External pipe to video encoder
+# Replacement for FFMPEG builtin encoder for ffmpeg_output_movies only.
+# The options movie_filename and timelapse_filename are also used
+# by the ffmpeg feature
+############################################################
+# Bool to enable or disable extpipe (default: off)
+use_extpipe off
+# External program (full path and opts) to pipe raw video to
+# Generally, use '-' for STDIN...
+; extpipe value
+############################################################
+# Snapshots (Traditional Periodic Webcam File Output)
+############################################################
+# Make automated snapshot every N seconds (default: 0 = disabled)
+snapshot_interval 0
+############################################################
+# Text Display
+# %Y = year, %m = month, %d = date,
+# %H = hour, %M = minute, %S = second, %T = HH:MM:SS,
+# %v = event, %q = frame number, %t = thread (camera) number,
+# %D = changed pixels, %N = noise level, \n = new line,
+# %i and %J = width and height of motion area,
+# %K and %L = X and Y coordinates of motion center
+# %C = value defined by text_event - do not use with text_event!
+# You can put quotation marks around the text to allow
+# leading spaces
+############################################################
+# Locate and draw a box around the moving object.
+# Valid values: on, off, preview (default: off)
+# Set to 'preview' will only draw a box in preview_shot pictures.
+locate_motion_mode off
+# Set the look and style of the locate box if enabled.
+# Valid values: box, redbox, cross, redcross (default: box)
+# Set to 'box' will draw the traditional box.
+# Set to 'redbox' will draw a red box.
+# Set to 'cross' will draw a little cross to mark center.
+# Set to 'redcross' will draw a little red cross to mark center.
+locate_motion_style box
+# Draws the timestamp using same options as C function strftime(3)
+# Default: %Y-%m-%d\n%T = date in ISO format and time in 24 hour clock
+# Text is placed in lower right corner
+text_right %Y-%m-%d\n%T-%q
+# Draw a user defined text on the images using same options as C function strftime(3)
+# Default: Not defined = no text
+# Text is placed in lower left corner
+; text_left value
+# Draw the number of changed pixed on the images (default: off)
+# Will normally be set to off except when you setup and adjust the motion settings
+# Text is placed in upper right corner
+text_changes off
+# This option defines the value of the special event conversion specifier %C
+# You can use any conversion specifier in this option except %C. Date and time
+# values are from the timestamp of the first image in the current event.
+# Default: %Y%m%d%H%M%S
+# The idea is that %C can be used filenames and text_left/right for creating
+# a unique identifier for each event.
+text_event %Y%m%d%H%M%S
+# Draw characters at twice normal size on images. (default: off)
+text_double on
+# Text to include in a JPEG EXIF comment
+# May be any text, including conversion specifiers.
+# The EXIF timestamp is included independent of this text.
+; exif_text value
+############################################################
+# Target Directories and filenames For Images And Films
+# For the options snapshot_, picture_, movie_ and timelapse_filename
+# you can use conversion specifiers
+# %Y = year, %m = month, %d = date,
+# %H = hour, %M = minute, %S = second,
+# %v = event, %q = frame number, %t = thread (camera) number,
+# %D = changed pixels, %N = noise level,
+# %i and %J = width and height of motion area,
+# %K and %L = X and Y coordinates of motion center
+# %C = value defined by text_event
+# Quotation marks round string are allowed.
+############################################################
+# Target base directory for pictures and films
+# Recommended to use absolute path. (Default: current working directory)
+target_dir /recordings
+# File path for snapshots (jpeg or ppm) relative to target_dir
+# Default: %v-%Y%m%d%H%M%S-snapshot
+# Default value is equivalent to legacy oldlayout option
+# For Motion 3.0 compatible mode choose: %Y/%m/%d/%H/%M/%S-snapshot
+# File extension .jpg or .ppm is automatically added so do not include this.
+# Note: A symbolic link called lastsnap.jpg created in the target_dir will always
+# point to the latest snapshot, unless snapshot_filename is exactly 'lastsnap'
+snapshot_filename %v-%Y%m%d%H%M%S-snapshot
+# File path for motion triggered images (jpeg or ppm) relative to target_dir
+# Default: %v-%Y%m%d%H%M%S-%q
+# Default value is equivalent to legacy oldlayout option
+# For Motion 3.0 compatible mode choose: %Y/%m/%d/%H/%M/%S-%q
+# File extension .jpg or .ppm is automatically added so do not include this
+# Set to 'preview' together with best-preview feature enables special naming
+# convention for preview shots. See motion guide for details
+picture_filename %v-%Y%m%d%H%M%S-%q
+# File path for motion triggered ffmpeg films (movies) relative to target_dir
+# Default: %v-%Y%m%d%H%M%S
+# Default value is equivalent to legacy oldlayout option
+# For Motion 3.0 compatible mode choose: %Y/%m/%d/%H%M%S
+# File extension .mpg or .avi is automatically added so do not include this
+# This option was previously called ffmpeg_filename
+movie_filename %v-%Y%m%d%H%M%S
+# File path for timelapse movies relative to target_dir
+# Default: %Y%m%d-timelapse
+# Default value is near equivalent to legacy oldlayout option
+# For Motion 3.0 compatible mode choose: %Y/%m/%d-timelapse
+# File extension .mpg is automatically added so do not include this
+timelapse_filename %Y%m%d-timelapse
+############################################################
+# Global Network Options
+############################################################
+# Enable or disable IPV6 for http control and stream (default: off)
+ipv6_enabled off
+############################################################
+# Live Stream Server
+############################################################
+# The mini-http server listens to this port for requests (default: 0 = disabled)
+stream_port 8081
+# Quality of the jpeg (in percent) images produced (default: 50)
+stream_quality 75
+# Output frames at 1 fps when no motion is detected and increase to the
+# rate given by stream_maxrate when motion is detected (default: off)
+stream_motion off
+# Maximum framerate for streams (default: 1)
+stream_maxrate 1
+# Restrict stream connections to localhost only (default: on)
+stream_localhost off
+# Limits the number of images per connection (default: 0 = unlimited)
+# Number can be defined by multiplying actual stream rate by desired number of seconds
+# Actual stream rate is the smallest of the numbers framerate and stream_maxrate
+stream_limit 0
+# Set the authentication method (default: 0)
+# 0 = disabled
+# 1 = Basic authentication
+# 2 = MD5 digest (the safer authentication)
+stream_auth_method 2
+# Authentication for the stream. Syntax username:password
+# Default: not defined (Disabled)
+stream_authentication loginname:loginpassword
+############################################################
+# HTTP Based Control
+############################################################
+# TCP/IP port for the http server to listen on (default: 0 = disabled)
+webcontrol_port 8080
+# Restrict control connections to localhost only (default: on)
+webcontrol_localhost off
+# Output for http server, select off to choose raw text plain (default: on)
+webcontrol_html_output on
+# Authentication for the http based control. Syntax username:password
+# Default: not defined (Disabled)
+webcontrol_authentication loginname:loginpassword
+############################################################
+# Tracking (Pan/Tilt)
+############################################################
+# Type of tracker (0=none (default), 1=stepper, 2=iomojo, 3=pwc, 4=generic, 5=uvcvideo, 6=servo)
+# The generic type enables the definition of motion center and motion size to
+# be used with the conversion specifiers for options like on_motion_detected
+track_type 0
+# Enable auto tracking (default: off)
+track_auto off
+# Serial port of motor (default: none)
+; track_port value
+# Motor number for x-axis (default: 0)
+track_motorx 0
+# Set motorx reverse (default: off)
+track_motorx_reverse off
+# Motor number for y-axis (default: 0)
+track_motory 0
+# Set motory reverse (default: off)
+track_motory_reverse off
+# Maximum value on x-axis (default: 0)
+track_maxx 0
+# Minimum value on x-axis (default: 0)
+track_minx 0
+# Maximum value on y-axis (default: 0)
+track_maxy 0
+# Minimum value on y-axis (default: 0)
+track_miny 0
+# Center value on x-axis (default: 0)
+track_homex 128
+# Center value on y-axis (default: 0)
+track_homey 128
+# ID of an iomojo camera if used (default: 0)
+track_iomojo_id 0
+# Angle in degrees the camera moves per step on the X-axis
+# with auto-track (default: 10)
+# Currently only used with pwc type cameras
+track_step_angle_x 10
+# Angle in degrees the camera moves per step on the Y-axis
+# with auto-track (default: 10)
+# Currently only used with pwc type cameras
+track_step_angle_y 10
+# Delay to wait for after tracking movement as number
+# of picture frames (default: 10)
+track_move_wait 10
+# Speed to set the motor to (stepper motor option) (default: 255)
+track_speed 255
+# Number of steps to make (stepper motor option) (default: 40)
+track_stepsize 40
+############################################################
+# External Commands, Warnings and Logging:
+# You can use conversion specifiers for the on_xxxx commands
+# %Y = year, %m = month, %d = date,
+# %H = hour, %M = minute, %S = second,
+# %v = event, %q = frame number, %t = thread (camera) number,
+# %D = changed pixels, %N = noise level,
+# %i and %J = width and height of motion area,
+# %K and %L = X and Y coordinates of motion center
+# %C = value defined by text_event
+# %f = filename with full path
+# %n = number indicating filetype
+# Both %f and %n are only defined for on_picture_save,
+# on_movie_start and on_movie_end
+# Quotation marks round string are allowed.
+############################################################
+# Do not sound beeps when detecting motion (default: on)
+# Note: Motion never beeps when running in daemon mode.
+quiet on
+# Command to be executed when an event starts. (default: none)
+# An event starts at first motion detected after a period of no motion defined by event_gap
+; on_event_start value
+# Command to be executed when an event ends after a period of no motion
+# (default: none). The period of no motion is defined by option event_gap.
+; on_event_end value
+# Command to be executed when a picture (.ppm|.jpg) is saved (default: none)
+# To give the filename as an argument to a command append it with %f
+; on_picture_save value
+# Command to be executed when a motion frame is detected (default: none)
+; on_motion_detected value
+# Command to be executed when motion in a predefined area is detected
+# Check option 'area_detect'. (default: none)
+; on_area_detected value
+# Command to be executed when a movie file (.mpg|.avi) is created. (default: none)
+# To give the filename as an argument to a command append it with %f
+; on_movie_start value
+# Command to be executed when a movie file (.mpg|.avi) is closed. (default: none)
+# To give the filename as an argument to a command append it with %f
+; on_movie_end value
+# Command to be executed when a camera can't be opened or if it is lost
+# NOTE: There is situations when motion don't detect a lost camera!
+# It depends on the driver, some drivers dosn't detect a lost camera at all
+# Some hangs the motion thread. Some even hangs the PC! (default: none)
+; on_camera_lost value
+############################################################
+# Common Options for database features.
+# Options require the database options to be active also.
+############################################################
+# Log to the database when creating motion triggered image file  (default: on)
+sql_log_picture on
+# Log to the database when creating a snapshot image file (default: on)
+sql_log_snapshot on
+# Log to the database when creating motion triggered movie file (default: off)
+sql_log_movie off
+# Log to the database when creating timelapse movie file (default: off)
+sql_log_timelapse off
+# SQL query string that is sent to the database
+# Use same conversion specifiers has for text features
+# Additional special conversion specifiers are
+# %n = the number representing the file_type
+# %f = filename with full path
+# Create tables :
+##
+# Mysql
+# CREATE TABLE security (camera int, filename char(80) not null, frame int, file_type int, time_stamp timestamp(14), event_time_stamp timestamp(14));
+#
+# Postgresql
+# CREATE TABLE security (camera int, filename char(80) not null, frame int, file_type int, time_stamp timestamp without time zone, event_time_stamp timestamp without time zone);
+#
+# Default value:
+# insert into security(camera, filename, frame, file_type, time_stamp, text_event) values('%t', '%f', '%q', '%n', '%Y-%m-%d %T', '%C')
+sql_query sql_query insert into security(camera, filename, frame, file_type, time_stamp, event_time_stamp) values('%t', '%f', '%q', '%n', '%Y-%m-%d %T', '%C')
+############################################################
+# Database Options
+############################################################
+# database type : mysql, postgresql, sqlite3 (default : not defined)
+; database_type value
+# database to log to (default: not defined)
+; database_dbname value
+# The host on which the database is located (default: not defined)
+database_host localhost
+# User account name for database (default: not defined)
+; database_user value
+# User password for database (default: not defined)
+; database_password value
+# Port on which the database is located (default: not defined)
+# mysql 3306 , postgresql 5432 (default: not defined)
+database_port 0
+############################################################
+# Video Loopback Device (vloopback project)
+############################################################
+# Output images to a video4linux loopback device
+# The value '-' means next available (default: not defined)
+; video_pipe value
+# Output motion images to a video4linux loopback device
+# The value '-' means next available (default: not defined)
+; motion_video_pipe value
+##############################################################
+# Thread config files - One for each camera.
+# Except if only one camera - You only need this config file.
+# If you have more than one camera you MUST define one thread
+# config file for each camera in addition to this config file.
+##############################################################
+; thread /usr/local/etc/thread1.conf
+</code>
+\\
+\\
+~~DISCUSSION:closed~~

Lunetikk's IT Wiki

User Tools

Site Tools

Differences

Page Tools